Examples Of Our Work

Sniper rifle built for Eric Sorensen chambered in 308 Winchester Match.

Rifle built for Jim Owens of National Match Rifle Rests, Inc.

This is a Smith & Wesson Model 66 .357 Magnum caliber revolver that was an issue duty weapon for the San Diego County Sheriff's Department. The weapon has been rebuilt, re-timed and had new springs installed. Custom work includes a trigger job, removal of the front sight, the hammer has been bobbed and a Hogue Monogrip has been installed.

Pat Walsh and his Remington 700 chambered in 22/250 Remington Match. The stainless steel receiver assembly has been cryoed, heat stress relieved, blue printed & the bolt raceway line bored out to .7050" with a custom built bolt .7035" diameter and a Sako extractor, extended bolt handle & bench rest firing pin assembly installed. The trigger is a Jewell (10 oz). The barrel is a McGowen Rifle Barrels, Premium Grade, 416 crucible SS, 1/8" twist, tapered to 1.0" muzzle diameter, finished length 28". The stock is an HS Precision Varmint and the barrel is glued into the stock and the receiver/trigger/bottom metal assembly has been free floated. The Leupold riflescope & Scoplevel (anti cant device) is attached to the rifle with Talley rings and bases.

Remington 700 Police Sniper in 308 Winchester owned by Officer Anthony Milton of Riverdale Police Department, Riverdale, IL. The barreled action assembly has been accurized and the barrel was cut at 18" finished length, providing 2637 fps to 2679 fps (Oehler Model 35P Proof Chronograph) with 168 grain Federal Gold Medal Match. The 168 grain Black Hills was slightly faster. The trigger is a rebuilt and re-sprung Remington 700 trigger assembly set at 3 lbs. The stock is an HS Precision Tactical reworked to bed the barrel & free float the receiver assembly.

Kyle Mayhall with his accurized Browning A Bolt Hunter chambered in 270 Winchester Match. The receiver/barrel assembly has been cryoed, heat stress relieved and the the receiver/bolt assembly was machined (receiver & bolt face trued, receiver & bolt locking lugs trued). The trigger was reworked and set at 2 lbs. The barrel is a factory Browning, button rifled Sporterweight @ 22" finished length. The barrel was then hand lapped, re-crowned, barrel set back approximately .10", re-chambered to minimum headspace. The metal parts were powder coated in both matte grey & black. The stock was stripped, sealed, refinished, pillar bedded and a recoil reducer & Pachmayr Decel pad were installed. The Shepherd Enterprises, Inc. 618-V1 rifle scope & Scoplevel are attached to the rifle using Talley rings & bases.

M24 Sniper Rifle chambered in 308 Winchester Match built for a military/security sub-contractor (un-named for security reasons) working in Afghanistan. This is a cryoed & heat stress relieved and then blue printed, Remington 700 BDL/SA receiver assembly with a Sako extractor and a Jewell trigger (2.5 lbs). The barrel is a free floated McGowen Rifle Barrels, Premium Grade, 416 crucible SS, 1/10" twist, tapered to .900" muzzle diameter, finished length 26". All metal parts finished with Birdsong Industries Black T finish in flat olive drab and flat black. The stock is a pillar bedded McMillan A5 with an adjustable cheek piece and adjustable for length of pull.

Charles Clement is at the ISRA Range, Bonfield, IL., with his Remington 700 BDL/LA chambered in 300 Remington Ultra Magnum Match. The receiver assembly has been cryoed, heat stress relieved, blue printed, with a Sako extractor, bench rest firing pin assembly and rebuilt Remington 700 trigger assembly (2.5 lbs). The barrel is a Shilen Inc., Select Match Grade, SS, 1/10 twist, #11 Straight Bull 1.20" X 28" finished length, 6 straight flutes. All metal parts are powder coated flat black. The laminated wood stock is from Boyd's Gunstock Industries, Inc. There are 2 recoil reducers in the buttstock & a Pachmayr Decel pad was installed. The barrel is bedded & the receiver assembly is free floated. The Shepherd Enterprises, Inc., 618-V1 riflescope & Scoplevel is attached to the rifle with Talley rings & bases.

Rifle built for Steve DeMarte. Remington 700 BDL chambered in 338 RUM Match @ minimum headspace. The rifle is barrel bedded with the receiver free floated. Blue printed receiver, bolt raceway line bored to .7050” diameter & a custom made bolt @.7035” diameter, Sako extractor, extended tactical bolt handle & knob, Tubb recoil lug, re-built & re-sprung Remington 700 trigger assembly set at 2.5 lbs, and an external bolt stop are installed. The barrel blank used is a McGowen Premium 416R Stainless Steel in a 1/10” twist rate, finished @ 28” long with a 1.200” diameter bull barrel contour. Finish coat is matte black powder coat. The stock is a rosewood laminate blank from Richard’s Micro-Fit Gunstocks, Inc. that was inletted by us to accept the barrel & free float the receiver, and then sanded & finish coated. 2 Edward's Recoil Reducers & a Pachmayr Decel Pad were installed to reduce felt recoil. 2 Uncle Mikes sling swivel studs were installed. The rifle scope is a Shepherd V1-6X18X40 with a Scoplevel anti-cant device mounted in Talley rings & bases.

^{This site designed by}

copyright © 2005  McIntyre Precision, Inc.  All rights reserved